Technical Info of Stub Ends (MSS SP-43)

stub end technical info

Schedule 10S

NPS	OD	T	G	F	R	kg
1/2	21.3	2.11	34.9	50.8	3.18	0.07
3/4	26.7	2.11	42.9	50.8	3.18	0.10
1	33.4	2.77	50.8	50.8	3.18	0.16
1¼	42.2	2.77	63.5	50.8	4.76	0.22
1½	48.3	2.77	73	50.8	6.35	0.25
2	60.3	2.77	92.1	63.5	7.94	0.43
2½	73	3.05	104.8	63.5	7.94	0.57
3	88.9	3.05	127	63.5	9.53	0.73
4	114.3	3.05	157.2	76.2	11.11	1.09
5	141.3	3.40	185.7	76.2	11.11	1.47
6	168.3	3.40	215.9	88.9	12.70	2.15
8	219.1	3.76	269.9	101.6	12.70	3.22
10	273.1	4.19	323.9	127	12.70	5.13
12	323.9	4.57	381	152.4	12.70	8.16
14	355.6	4.78	412.8	152.4	12.70	10.89
16	406.4	4.78	469.9	152.4	12.70	12.70
18	457.2	4.78	533.4	152.4	12.70	17.24
20	508	5.54	584.2	152.4	12.70	21.77
24	609.6	6.35	692.2	152.4	12.70	27.22
Dimensions are in millimeters unless otherwise indicated. Weights are in kilograms and approximately given.

Dimensional Tolerances of Stub Ends MSS SP-43

Nominal Pipe Size	1/2 up to 2½	3 to 3½	4	5 to 8	10 to 18	20 to 24
Outside Diameter at Welding End (OD)	0.8	0.8	0.8	+ 1.6 - 0.8	+ 2.29 - 0.76	+ 3.05 - 0.76
Overall Length (F)	1.6	1.6	1.6	1.6	2	2
Outside Diameter of Lap (G)	+ 0 - 0.76	+ 0 - 0.76	+ 0 - 0.76	+ 0 - 0.76	+ 0 - 1.6	+ 0 - 1.6
Thickness of Lap (T)	+ 1.52 - 0	+ 1.52 - 0	+ 1.52 - 0	+ 1.52 - 0	+ 1.52 - 0	+ 1.52 - 0
Fillet Radius of Lap (R)	+ 0 - 0.76	+ 0 - 0.76	+ 0 - 1.6	+ 0 - 1.6	+ 0 - 1.6	+ 0 - 1.6
Wall Thickness (t)	Not less than 87.5% of Nominal Wall Thickness

Dimensional tolerances are in millimeters unless otherwise indicated.

Note:
MSS SP-43 only covers stainless steel buttweld fittings made for use with Schedule 5S and 10S pipe and Stub Ends suitable for use with Schedule 40S pipe, as defined in ASME B36.19. The dimensions and dimensional tolerances defined in MSS SP-43 are substantially the same as those in ASME B16.9 specifications from NPS 1/2 - NPS 24. Except with regard to the outside diameter at the bevel.